Pro Audio Systems

• Technical Specifications

• System Type Subwoofer-Bandpass
• Frequency Response (-3dB) (1) 37Hz - 80Hz
• Lowpass Filter A on
• Frequency Response (-3dB) (1) 37Hz - 110Hz
• Lowpass Filter B on
• Frequency Response (-10dB) (1) 32Hz - 80Hz
• Lowpass Filter A on
• Frequency Response (-10dB) (1) 32Hz - 110Hz
• Lowpass Filter B on
• Rated Maximum SPL (2) Average: 118dB
• Peak: 124dB
• Driver Complement 250mm (10.00”) high excursion bass driver
• Crossover User Selectable LPF
• Distortion 10% Full Power (12.7V)
• 2nd Harmonic
• 40Hz: 2.27%
• 100kHz: 1.79%
• 3rd Harmonic
• 40Hz: 0.73%
• 100kHz: 1.27%
• 1% Full Power (4V)
• 2nd Harmonic
• 40Hz: 0.57%
• 100kHz: 0.61%
• 3rd Harmonic
• 40Hz: 0.47%
• 100kHz: 1.37%
• Construction
• Enclosure 50 litre internally braced 15mm (0.62”) MDF bandpass enclosure
• Finish Textured black or white paint with custom colours on request
• Connectors 1 x female XLR (input)
• 1 male XLR (link)
• 1 x Neutrik Powercon
• Controls & Indicators Level control
• Power LED (blue)
• Signal LED (green)
• Limit LED (red)
• Full range / high pass switch (110Hz)
• Power switch
• Fittings 2 x Port aperture blanking plates to allow the bass ports to be moved to another facia
• 8 x M10 Flying inserts
• 2 x recessed carrying handles
• Blanking plate for optional VTH pole mount
• 4 x rubber feet
• Dimensions (HxWxD) 355 x 385 x 590mm
• (13.98 x 14.37 x 23.23”)
• Weight 18kg
• (39.6lbs)
• Electronics
• Maximum signal input for clip Input attenuator at minimum:
• +18dBu
• Input attenuator at maximum:
• +5dBu
• Output noise -105dB unweighted, referenced to maximum output (22kHz bandwidth)
• Efficiency >90% typically
• Damping Factor 400 ref 8 Ohms
• Distortion <0.05% @ 1kHz -3dB output (22kHz bandwidth)
• Input Impedance 5.6kOhms unbalanced
• 11.2kOhms balanced
• Protection systems
• Over Current Excessive over current causes shutdown
• Temperature Limiters applied
• Brownout Automatic protection & recovery
• Mains Inrush current limiting
• Indicators 1x Limit LED
• 1x Signal LED
• 1x Power LED
• Number of channels One
• System Type Class D
• PSU Specifications
• Input Connector Locking Neutrik Powercon
• Voltage Selection Automatic (115 / 230V, 45 - 65Hz)
• Type High current, high frequency switch mode
• Efficiency >90% typical
• Input voltage 100v / 115v / 230v nominal
• +/-10%
• Mains fuse External
• Fuse type T10AT
• Other features Automatic soft start

• Features

• A switch on the rear panel of the full range models allows selection between Full Range or High Pass modes, with High Pass allowing a speaker to be mounted in close proximity to a boundary or simply to increase headroom.
  
• High pass mode also enables a simple top box and subwoofer combination to be created without the need for an external crossover. Two low pass setting options on the subwoofer amplifiers fully optimise integration with the full range units.
  
• The POWERVS10 BP utilises a single high efficiency 250mm (10.00”) drive unit in a compact and sturdy, black or white painted MDF cabinet. The design concept also allows discreet placement, for instance unobtrusively incorporated into fixed furnishings such as underneath seating or the bar in cafes and bars.
  
• The install placement is made even easier as the design incorporates moveable bass port tubes and blanking plates that can be swapped from the side to the end panel, allowing the unit to be installed in various orientations. M10 rigging points are also provided to allow permanent installation.

Related Products

No related products found.